Skip to content
Level 2 charging

Level 2 EV Charger Installation in Fishers

Dedicated 240-volt charging for homes from the Nickel Plate District out to Geist and along 116th Street.

Get your Level 2 quote — (317) 597-1431
Level 2 EV charger mounted on a garage wall with its cable holstered

Home Charging That Keeps Up With How You Actually Drive

A Level 2 charger is the difference between plugging in and genuinely not thinking about range again. Running on 240 volts, it adds somewhere between 20 and 40 miles of range an hour depending on the unit and the car, which means a Fishers commute down I-69 to the north side of Indianapolis is replaced overnight with capacity to spare. Most people call us within a week of taking delivery of a new EV, once the included 120-volt cable has shown them what three miles an hour feels like. Fishers EV Charger Installation handles the whole piece: the load calculation on your existing service, the dedicated circuit, the mounting, the permit and the inspection. A typical visit starts with us opening the panel and measuring what is actually there, because the quote depends on headroom and run length more than on anything else.

What a Level 2 Install Covers

Every Level 2 job is quoted line by line. Here is what those lines usually consist of.

  • Service load calculation

    We calculate your home's existing demand against the panel's rating before anything is specified, so the charger we recommend is one the service can actually carry continuously.

  • Dedicated 240V branch circuit

    A new two-pole breaker and a home run sized to the charger, never a shared or re-purposed circuit. Continuous-load rules mean the breaker is sized above the charger's draw, not equal to it.

  • Correct conductor sizing for the run

    Wire gauge is chosen for the actual distance from panel to charger, which is why a long run to a detached garage in Geist costs more than a run to a panel on the garage wall.

  • Conduit, routing and making good

    Surface conduit, in-wall runs or a combination, routed to keep the finish tidy. Where drywall has to open, we cut clean and patch back.

  • Charger mounting and levelling

    The unit is mounted at a working height on structure, not drywall anchors, with the cable holster positioned so the lead reaches the car's port without stretching across the bay.

  • GFCI and disconnect provisions where required

    Outdoor and garage-adjacent installs get the protection and local disconnect the code calls for in that location rather than a generic approach.

  • Commissioning and amperage configuration

    The charger's output is set to match the circuit it is on, connected to your Wi-Fi where the unit supports it, and tested with the car plugged in before we leave.

  • Permit filed and inspection attended

    The City of Fishers permit is pulled under the job, the inspection is booked, and one of our installers is on site for it.

  • Labelling and documentation

    The new breaker is labelled in the panel directory, and you get the permit record, the itemized invoice and the equipment details together.

  • Warranty registration

    We register the unit with the manufacturer so its warranty actually starts, and our own workmanship warranty sits alongside it.

Three Steps From Call to Charging

  1. 01

    Panel visit and written quote

    We come out, open the panel, measure the run and ask where you want the unit. You will see us photograph the panel directory and count spare spaces. The quote comes back itemized, usually the same day, and it holds unless something behind the wall changes the scope.

  2. 02

    Permit and scheduling

    Once you approve the figure, we file the permit and book the install. For a standard attached-garage job this is a single visit of a few hours. We give you a window and we hold it, because the drive from one side of Hamilton County to the other is short.

  3. 03

    Install, inspection and handover

    The circuit goes in, the charger is mounted and commissioned, and we plug your car in to confirm it draws what it should. The inspector visits, signs it off, and you get the paperwork package for your rebate claim.

Why This Install Goes Right the First Time

The load calculation is real, not assumed

A lot of failed Level 2 installs trace back to someone counting empty breaker slots and calling it capacity. We calculate demand properly, and if the answer is that your service needs upgrading first, you hear it at quote stage rather than after the charger is on the wall.

Breaker and wire sized for continuous load

EV charging runs at full draw for hours, which is why the code treats it differently from a dryer circuit. Getting that derating right is the single most common thing we find missing on installs we are called back to fix.

One crew, one price, one accountable warranty

The people who quote the job are the people who wire it. There is no subcontractor in the middle, so when you call about anything afterwards you are talking to someone who was there.

  • Licensed & Insured
  • Flat Written Pricing
  • Typically a Single-Visit Install
  • EVITP-Certified Installers
  • Permit Pulled and Inspected

Get a Level 2 Charger on Your Wall

Tell us the car and we will tell you the amperage it can actually use, then price the circuit to match. You will have an itemized figure before anything is ordered, and the permit is ours to handle. Most Fishers homes are charging within a week of approving the quote.

Book your panel visit — (317) 597-1431